国产毛片a精品毛-国产毛片黄片-国产毛片久久国产-国产毛片久久精品-青娱乐极品在线-青娱乐精品

電子工程網

標題: MYZR IMX6 EK200 RTL8188EUS WIFI AP [打印本頁]

作者: myzr123 時間: 2018-7-1 21:45
標題: MYZR IMX6 EK200 RTL8188EUS WIFI AP
主機平臺： UBUNTU14.04
硬件平臺：明遠智睿MY-IMX6-EK200
編譯器:    gcc-linaro-arm-linux-gnueabihf-4.9-2014.09_linux.tar.xz
buildroot版本：buildroot-2017.02.5.tar.bz2
內核版本    linux-3.14.52

1.內核需要配置,配置完直接編譯zImage
CONFIG_CFG80211=y
CONFIG_MAC80211=y
CONFIG_HOSTAP=y
CONFIG_USB_USBNET=y

2. 編譯rtl8188eus模塊
源碼包：rtl8188EUS_linux_v4.3.0.9_15178.20150907%28myimx6%29.tar.xz
$ tar xvf rtl8188EUS_linux_v4.3.0.9_15178.20150907%28myimx6%29.tar.xz
$ cd rtl8188EUS_linux_v4.3.0.9_15178.20150907
$ vim Makefile
修改增加（源碼路徑和交叉編譯工具路徑）
ifeq ($(CONFIG_PLATFORM_ARM_MYIMX6), y)
EXTRA_CFLAGS += -DCONFIG_LITTLE_ENDIAN
ARCH := arm
CROSS_COMPILE ?= ~/IMX6/gcc-linaro-arm-linux-gnueabihf-4.9-2014.09_linux/bin/arm-linux-gnueabihf-
KVER  ?= 3.14.52
KSRC ?= /home/linyn/rs485/linux-custom
endif

vim include/autoconf.h
修改：
#define CONFIG_IOCTL_CFG80211
#ifdef CONFIG_IOCTL_CFG80211
#define RTW_USE_CFG80211_STA_EVENT
//#defineCONFIG_CFG80211_FORCE_COMPATIBLE_2_6_37_UNDER
//#define CONFIG_DEBUG_CFG80211 1
#endif
...
...
#define CONFIG_CONCURRENT_MODE
…
最后編譯模塊8188eu.ko

3.移植hostapd和dhcpd
a)如果是用buildroot編譯的話，直接用make menuconfig配置就行,這里不講了
b)或者自己獨立編譯hostapd和dhcpd

4.配置hostapd和dhcpd
a) 配置hostapd
vim /etc/hostapd.conf
interface=wlan0
driver=nl80211
ssid=MYZR
channel=9
hw_mode=g
macaddr_acl=0
ignore_broadcast_ssid=0
auth_algs=1
wpa=3
wpa_passphrase=12345678
wpa_key_mgmt=WPA-PSK
wpa_pairwise=TKIP
rsn_pairwise=CCMP

b)配置dhcpd
touch  /var/db/dhcpd.leases

vim  /etc/dhcpd.conf
在最后增加：
subnet 192.168.155.0 netmask 255.255.255.0
{
range 192.168.155.2 192.168.155.10;
option domain-name-servers 8.8.8.8;
option routers 192.168.155.1;
}

5.啟動熱點和自動獲取IP
echo "1" >/proc/sys/net/ipv4/ip_forward
hostapd -B /etc/hostapd.conf
ifconfig wlan0 192.168.155.1
dhcpd wlan0
看圖片“WIFIAP.png”

最后通過手機，可以搜索“MYZR”的熱點，直接輸入密碼“12345678”，這樣手機WIF連接成功，會自動分別192.168.155.*的IP.

注意：以上雖然分配到IP，但是不能上網，需要使用iptables開啟本地的SNAT
經過前面幾個步驟，無線網卡已經可以自動分配IP，現在只需要把無線網卡的數據都經過eth0(有線網絡)發到外網去，這就需要IP轉發了。
6.配置內核
Networking support  --->
Networking options  --->Network packet filtering framework (Netfilter)  --->
Core Netfilter Configuration  --->  //除了下面列出的其他全選
< > Transparent proxying support (EXPERIMENTAL)
< > set target and match support
< > CHECKSUM target support
< > "CT" target support
< > "DSCP" and "TOS" target support
< > "NOTRACK" target support
< > "TCPOPTSTRIP" target support (EXPERIMENTAL)
< > "dscp" and "tos" match support
< > "ipvs" match support
<*> IP set support  --->
(256) Maximum number of IP sets
<*> bitmap:ip set support
<*> bitmap:ip,mac set support
<*> bitmap:port set support
<*> list:set set support
<*> IP virtual server support  ---> //除了下面列出的其他全選
[ ] IP virtual server debugging
[ ] SCTP load balancing support
< > FTP protocol helper
< > SIP persistence engine
IP: Netfilter Configuration  ---> //里面的全選
<*> RF switch subsystem support  --->
//注意要選最后一項，不然在使用hostapd命令時會出錯，“rfkill: Cannot open RFKILL control device”.
7.移植iptables直接用buildroot配置編譯就行，或者獨立編譯，這里不講了udhcpc -i eth0
iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
這樣連接wifi，手機和ubuntu的WPA2-PSK的無線wifi AP設置完畢，可以正常使用了。

歡迎光臨電子工程網 (http://www.qingdxww.cn/)